RP2040_SVD.PPB

Entities

Record Types

Subtypes

Variables

Description

------------- Registers -- -------------

AIRCR_Register

type AIRCR_Register is record
   Reserved_0_0  : HAL.Bit := 16#0#;
   VECTCLRACTIVE : Boolean := False;
   SYSRESETREQ   : Boolean := False;
   Reserved_3_14 : HAL.UInt12 := 16#0#;
   ENDIANESS     : Boolean := False;
   VECTKEY       : AIRCR_VECTKEY_Field := 16#0#;
end record;
Record fields
Reserved_0_0

Clears all active state information for fixed and configurable exceptions. This bit: is self-clearing, can only be set by the DAP when the core is halted. When set: clears all active exception status of the processor, forces a return to Thread mode, forces an IPSR of 0. A debugger must re-initialize the stack.

VECTCLRACTIVE

Writing 1 to this bit causes the SYSRESETREQ signal to the outer system to be asserted to request a reset. The intention is to force a large system reset of all major components except for debug. The C_HALT bit in the DHCSR is cleared as a result of the system reset requested. The debugger does not lose contact with the device.

SYSRESETREQ

unspecified

Reserved_3_14

Read-only. Data endianness implemented:\n 0 = Little-endian.

ENDIANESS

Register key:\n Reads as Unknown\n On writes, write 0x05FA to VECTKEY, otherwise the write is ignored.

VECTKEY

AIRCR_VECTKEY_Field

subtype AIRCR_VECTKEY_Field is HAL.UInt16;

CCR_Register

type CCR_Register is record
   Reserved_0_2   : HAL.UInt3;
   UNALIGN_TRP    : Boolean;
   Reserved_4_8   : HAL.UInt5;
   STKALIGN       : Boolean;
   Reserved_10_31 : HAL.UInt22;
end record;
Record fields
Reserved_0_2

Read-only. Always reads as one, indicates that all unaligned accesses generate a HardFault.

UNALIGN_TRP

unspecified

Reserved_4_8

Read-only. Always reads as one, indicates 8-byte stack alignment on exception entry. On exception entry, the processor uses bit[9] of the stacked PSR to indicate the stack alignment. On return from the exception it uses this stacked bit to restore the correct stack alignment.

STKALIGN

unspecified

Reserved_10_31

CPUID_ARCHITECTURE_Field

subtype CPUID_ARCHITECTURE_Field is HAL.UInt4;

CPUID_IMPLEMENTER_Field

subtype CPUID_IMPLEMENTER_Field is HAL.UInt8;

CPUID_PARTNO_Field

subtype CPUID_PARTNO_Field is HAL.UInt12;

CPUID_Register

type CPUID_Register is record
   REVISION     : CPUID_REVISION_Field;
   PARTNO       : CPUID_PARTNO_Field;
   ARCHITECTURE : CPUID_ARCHITECTURE_Field;
   VARIANT      : CPUID_VARIANT_Field;
   IMPLEMENTER  : CPUID_IMPLEMENTER_Field;
end record;
Record fields
REVISION

Read-only. Number of processor within family: 0xC60 = Cortex-M0+

PARTNO

Read-only. Constant that defines the architecture of the processor:\n 0xC = ARMv6-M architecture.

ARCHITECTURE

Read-only. Major revision number n in the rnpm revision status:\n 0x0 = Revision 0.

VARIANT

Read-only. Implementor code: 0x41 = ARM

IMPLEMENTER

CPUID_REVISION_Field

subtype CPUID_REVISION_Field is HAL.UInt4;

CPUID_VARIANT_Field

subtype CPUID_VARIANT_Field is HAL.UInt4;

ICSR_Register

type ICSR_Register is record
   VECTACTIVE     : ICSR_VECTACTIVE_Field := 16#0#;
   Reserved_9_11  : HAL.UInt3 := 16#0#;
   VECTPENDING    : ICSR_VECTPENDING_Field := 16#0#;
   Reserved_21_21 : HAL.Bit := 16#0#;
   ISRPENDING     : Boolean := False;
   ISRPREEMPT     : Boolean := False;
   Reserved_24_24 : HAL.Bit := 16#0#;
   PENDSTCLR      : Boolean := False;
   PENDSTSET      : Boolean := False;
   PENDSVCLR      : Boolean := False;
   PENDSVSET      : Boolean := False;
   Reserved_29_30 : HAL.UInt2 := 16#0#;
   NMIPENDSET     : Boolean := False;
end record;
Record fields
VECTACTIVE

unspecified

Reserved_9_11

Read-only. Indicates the exception number for the highest priority pending exception: 0 = no pending exceptions. Non zero = The pending state includes the effect of memory-mapped enable and mask registers. It does not include the PRIMASK special-purpose register qualifier.

VECTPENDING

unspecified

Reserved_21_21

Read-only. External interrupt pending flag

ISRPENDING

Read-only. The system can only access this bit when the core is halted. It indicates that a pending interrupt is to be taken in the next running cycle. If C_MASKINTS is clear in the Debug Halting Control and Status Register, the interrupt is serviced.

ISRPREEMPT

unspecified

Reserved_24_24

SysTick exception clear-pending bit.\n Write:\n 0 = No effect.\n 1 = Removes the pending state from the SysTick exception.\n This bit is WO. On a register read its value is Unknown.

PENDSTCLR

SysTick exception set-pending bit.\n Write:\n 0 = No effect.\n 1 = Changes SysTick exception state to pending.\n Read:\n 0 = SysTick exception is not pending.\n 1 = SysTick exception is pending.

PENDSTSET

PendSV clear-pending bit.\n Write:\n 0 = No effect.\n 1 = Removes the pending state from the PendSV exception.

PENDSVCLR

PendSV set-pending bit.\n Write:\n 0 = No effect.\n 1 = Changes PendSV exception state to pending.\n Read:\n 0 = PendSV exception is not pending.\n 1 = PendSV exception is pending.\n Writing 1 to this bit is the only way to set the PendSV exception state to pending.

PENDSVSET

unspecified

Reserved_29_30

Setting this bit will activate an NMI. Since NMI is the highest priority exception, it will activate as soon as it is registered.\n NMI set-pending bit.\n Write:\n 0 = No effect.\n 1 = Changes NMI exception state to pending.\n Read:\n 0 = NMI exception is not pending.\n 1 = NMI exception is pending.\n Because NMI is the highest-priority exception, normally the processor enters the NMI\n exception handler as soon as it detects a write of 1 to this bit. Entering the handler then clears\n this bit to 0. This means a read of this bit by the NMI exception handler returns 1 only if the\n NMI signal is reasserted while the processor is executing that handler.

NMIPENDSET

ICSR_VECTACTIVE_Field

subtype ICSR_VECTACTIVE_Field is HAL.UInt9;

ICSR_VECTPENDING_Field

subtype ICSR_VECTPENDING_Field is HAL.UInt9;

MPU_CTRL_Register

type MPU_CTRL_Register is record
   ENABLE        : Boolean := False;
   HFNMIENA      : Boolean := False;
   PRIVDEFENA    : Boolean := False;
   Reserved_3_31 : HAL.UInt29 := 16#0#;
end record;
Record fields
ENABLE

Controls the use of the MPU for HardFaults and NMIs. Setting this bit when ENABLE is clear results in UNPREDICTABLE behaviour.\n When the MPU is enabled:\n 0 = MPU is disabled during HardFault and NMI handlers, regardless of the value of the ENABLE bit.\n 1 = the MPU is enabled during HardFault and NMI handlers.

HFNMIENA

Controls whether the default memory map is enabled as a background region for privileged accesses. This bit is ignored when ENABLE is clear.\n 0 = If the MPU is enabled, disables use of the default memory map. Any memory access to a location not\n covered by any enabled region causes a fault.\n 1 = If the MPU is enabled, enables use of the default memory map as a background region for privileged software accesses.\n When enabled, the background region acts as if it is region number -1. Any region that is defined and enabled has priority over this default map.

PRIVDEFENA

unspecified

Reserved_3_31

MPU_RASR_ATTRS_Field

subtype MPU_RASR_ATTRS_Field is HAL.UInt16;

MPU_RASR_Register

type MPU_RASR_Register is record
   ENABLE       : Boolean := False;
   SIZE         : MPU_RASR_SIZE_Field := 16#0#;
   Reserved_6_7 : HAL.UInt2 := 16#0#;
   SRD          : MPU_RASR_SRD_Field := 16#0#;
   ATTRS        : MPU_RASR_ATTRS_Field := 16#0#;
end record;
Record fields
ENABLE

Indicates the region size. Region size in bytes = 2^(SIZE+1). The minimum permitted value is 7 (b00111) = 256Bytes

SIZE

unspecified

Reserved_6_7

Subregion Disable. For regions of 256 bytes or larger, each bit of this field controls whether one of the eight equal subregions is enabled.

SRD

The MPU Region Attribute field. Use to define the region attribute control.\n 28 = XN: Instruction access disable bit:\n 0 = Instruction fetches enabled.\n 1 = Instruction fetches disabled.\n 26:24 = AP: Access permission field\n 18 = S: Shareable bit\n 17 = C: Cacheable bit\n 16 = B: Bufferable bit

ATTRS

MPU_RASR_SIZE_Field

subtype MPU_RASR_SIZE_Field is HAL.UInt5;

MPU_RASR_SRD_Field

subtype MPU_RASR_SRD_Field is HAL.UInt8;

MPU_RBAR_ADDR_Field

subtype MPU_RBAR_ADDR_Field is HAL.UInt24;

MPU_RBAR_REGION_Field

subtype MPU_RBAR_REGION_Field is HAL.UInt4;

MPU_RBAR_Register

type MPU_RBAR_Register is record
   REGION       : MPU_RBAR_REGION_Field := 16#0#;
   VALID        : Boolean := False;
   Reserved_5_7 : HAL.UInt3 := 16#0#;
   ADDR         : MPU_RBAR_ADDR_Field := 16#0#;
end record;
Record fields
REGION

On writes, indicates whether the write must update the base address of the region identified by the REGION field, updating the MPU_RNR to indicate this new region.\n Write:\n 0 = MPU_RNR not changed, and the processor:\n Updates the base address for the region specified in the MPU_RNR.\n Ignores the value of the REGION field.\n 1 = The processor:\n Updates the value of the MPU_RNR to the value of the REGION field.\n Updates the base address for the region specified in the REGION field.\n Always reads as zero.

VALID

unspecified

Reserved_5_7

Base address of the region.

ADDR

MPU_RNR_REGION_Field

subtype MPU_RNR_REGION_Field is HAL.UInt4;

MPU_RNR_Register

type MPU_RNR_Register is record
   REGION        : MPU_RNR_REGION_Field := 16#0#;
   Reserved_4_31 : HAL.UInt28 := 16#0#;
end record;
Record fields
REGION

unspecified

Reserved_4_31

MPU_TYPE_DREGION_Field

subtype MPU_TYPE_DREGION_Field is HAL.UInt8;

MPU_TYPE_IREGION_Field

subtype MPU_TYPE_IREGION_Field is HAL.UInt8;

MPU_TYPE_Register

type MPU_TYPE_Register is record
   SEPARATE_k     : Boolean;
   Reserved_1_7   : HAL.UInt7;
   DREGION        : MPU_TYPE_DREGION_Field;
   IREGION        : MPU_TYPE_IREGION_Field;
   Reserved_24_31 : HAL.UInt8;
end record;
Record fields
SEPARATE_k

unspecified

Reserved_1_7

Read-only. Number of regions supported by the MPU.

DREGION

Read-only. Instruction region. Reads as zero as ARMv6-M only supports a unified MPU.

IREGION

unspecified

Reserved_24_31

NVIC_IPR0_IP_0_Field

subtype NVIC_IPR0_IP_0_Field is HAL.UInt2;

NVIC_IPR0_IP_1_Field

subtype NVIC_IPR0_IP_1_Field is HAL.UInt2;

NVIC_IPR0_IP_2_Field

subtype NVIC_IPR0_IP_2_Field is HAL.UInt2;

NVIC_IPR0_IP_3_Field

subtype NVIC_IPR0_IP_3_Field is HAL.UInt2;

NVIC_IPR0_Register

type NVIC_IPR0_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_0           : NVIC_IPR0_IP_0_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_1           : NVIC_IPR0_IP_1_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_2           : NVIC_IPR0_IP_2_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_3           : NVIC_IPR0_IP_3_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 0

IP_0

unspecified

Reserved_8_13

Priority of interrupt 1

IP_1

unspecified

Reserved_16_21

Priority of interrupt 2

IP_2

unspecified

Reserved_24_29

Priority of interrupt 3

IP_3

NVIC_IPR1_IP_4_Field

subtype NVIC_IPR1_IP_4_Field is HAL.UInt2;

NVIC_IPR1_IP_5_Field

subtype NVIC_IPR1_IP_5_Field is HAL.UInt2;

NVIC_IPR1_IP_6_Field

subtype NVIC_IPR1_IP_6_Field is HAL.UInt2;

NVIC_IPR1_IP_7_Field

subtype NVIC_IPR1_IP_7_Field is HAL.UInt2;

NVIC_IPR1_Register

type NVIC_IPR1_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_4           : NVIC_IPR1_IP_4_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_5           : NVIC_IPR1_IP_5_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_6           : NVIC_IPR1_IP_6_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_7           : NVIC_IPR1_IP_7_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 4

IP_4

unspecified

Reserved_8_13

Priority of interrupt 5

IP_5

unspecified

Reserved_16_21

Priority of interrupt 6

IP_6

unspecified

Reserved_24_29

Priority of interrupt 7

IP_7

NVIC_IPR2_IP_10_Field

subtype NVIC_IPR2_IP_10_Field is HAL.UInt2;

NVIC_IPR2_IP_11_Field

subtype NVIC_IPR2_IP_11_Field is HAL.UInt2;

NVIC_IPR2_IP_8_Field

subtype NVIC_IPR2_IP_8_Field is HAL.UInt2;

NVIC_IPR2_IP_9_Field

subtype NVIC_IPR2_IP_9_Field is HAL.UInt2;

NVIC_IPR2_Register

type NVIC_IPR2_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_8           : NVIC_IPR2_IP_8_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_9           : NVIC_IPR2_IP_9_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_10          : NVIC_IPR2_IP_10_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_11          : NVIC_IPR2_IP_11_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 8

IP_8

unspecified

Reserved_8_13

Priority of interrupt 9

IP_9

unspecified

Reserved_16_21

Priority of interrupt 10

IP_10

unspecified

Reserved_24_29

Priority of interrupt 11

IP_11

NVIC_IPR3_IP_12_Field

subtype NVIC_IPR3_IP_12_Field is HAL.UInt2;

NVIC_IPR3_IP_13_Field

subtype NVIC_IPR3_IP_13_Field is HAL.UInt2;

NVIC_IPR3_IP_14_Field

subtype NVIC_IPR3_IP_14_Field is HAL.UInt2;

NVIC_IPR3_IP_15_Field

subtype NVIC_IPR3_IP_15_Field is HAL.UInt2;

NVIC_IPR3_Register

type NVIC_IPR3_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_12          : NVIC_IPR3_IP_12_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_13          : NVIC_IPR3_IP_13_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_14          : NVIC_IPR3_IP_14_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_15          : NVIC_IPR3_IP_15_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 12

IP_12

unspecified

Reserved_8_13

Priority of interrupt 13

IP_13

unspecified

Reserved_16_21

Priority of interrupt 14

IP_14

unspecified

Reserved_24_29

Priority of interrupt 15

IP_15

NVIC_IPR4_IP_16_Field

subtype NVIC_IPR4_IP_16_Field is HAL.UInt2;

NVIC_IPR4_IP_17_Field

subtype NVIC_IPR4_IP_17_Field is HAL.UInt2;

NVIC_IPR4_IP_18_Field

subtype NVIC_IPR4_IP_18_Field is HAL.UInt2;

NVIC_IPR4_IP_19_Field

subtype NVIC_IPR4_IP_19_Field is HAL.UInt2;

NVIC_IPR4_Register

type NVIC_IPR4_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_16          : NVIC_IPR4_IP_16_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_17          : NVIC_IPR4_IP_17_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_18          : NVIC_IPR4_IP_18_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_19          : NVIC_IPR4_IP_19_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 16

IP_16

unspecified

Reserved_8_13

Priority of interrupt 17

IP_17

unspecified

Reserved_16_21

Priority of interrupt 18

IP_18

unspecified

Reserved_24_29

Priority of interrupt 19

IP_19

NVIC_IPR5_IP_20_Field

subtype NVIC_IPR5_IP_20_Field is HAL.UInt2;

NVIC_IPR5_IP_21_Field

subtype NVIC_IPR5_IP_21_Field is HAL.UInt2;

NVIC_IPR5_IP_22_Field

subtype NVIC_IPR5_IP_22_Field is HAL.UInt2;

NVIC_IPR5_IP_23_Field

subtype NVIC_IPR5_IP_23_Field is HAL.UInt2;

NVIC_IPR5_Register

type NVIC_IPR5_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_20          : NVIC_IPR5_IP_20_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_21          : NVIC_IPR5_IP_21_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_22          : NVIC_IPR5_IP_22_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_23          : NVIC_IPR5_IP_23_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 20

IP_20

unspecified

Reserved_8_13

Priority of interrupt 21

IP_21

unspecified

Reserved_16_21

Priority of interrupt 22

IP_22

unspecified

Reserved_24_29

Priority of interrupt 23

IP_23

NVIC_IPR6_IP_24_Field

subtype NVIC_IPR6_IP_24_Field is HAL.UInt2;

NVIC_IPR6_IP_25_Field

subtype NVIC_IPR6_IP_25_Field is HAL.UInt2;

NVIC_IPR6_IP_26_Field

subtype NVIC_IPR6_IP_26_Field is HAL.UInt2;

NVIC_IPR6_IP_27_Field

subtype NVIC_IPR6_IP_27_Field is HAL.UInt2;

NVIC_IPR6_Register

type NVIC_IPR6_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_24          : NVIC_IPR6_IP_24_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_25          : NVIC_IPR6_IP_25_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_26          : NVIC_IPR6_IP_26_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_27          : NVIC_IPR6_IP_27_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 24

IP_24

unspecified

Reserved_8_13

Priority of interrupt 25

IP_25

unspecified

Reserved_16_21

Priority of interrupt 26

IP_26

unspecified

Reserved_24_29

Priority of interrupt 27

IP_27

NVIC_IPR7_IP_28_Field

subtype NVIC_IPR7_IP_28_Field is HAL.UInt2;

NVIC_IPR7_IP_29_Field

subtype NVIC_IPR7_IP_29_Field is HAL.UInt2;

NVIC_IPR7_IP_30_Field

subtype NVIC_IPR7_IP_30_Field is HAL.UInt2;

NVIC_IPR7_IP_31_Field

subtype NVIC_IPR7_IP_31_Field is HAL.UInt2;

NVIC_IPR7_Register

type NVIC_IPR7_Register is record
   Reserved_0_5   : HAL.UInt6 := 16#0#;
   IP_28          : NVIC_IPR7_IP_28_Field := 16#0#;
   Reserved_8_13  : HAL.UInt6 := 16#0#;
   IP_29          : NVIC_IPR7_IP_29_Field := 16#0#;
   Reserved_16_21 : HAL.UInt6 := 16#0#;
   IP_30          : NVIC_IPR7_IP_30_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   IP_31          : NVIC_IPR7_IP_31_Field := 16#0#;
end record;
Record fields
Reserved_0_5

Priority of interrupt 28

IP_28

unspecified

Reserved_8_13

Priority of interrupt 29

IP_29

unspecified

Reserved_16_21

Priority of interrupt 30

IP_30

unspecified

Reserved_24_29

Priority of interrupt 31

IP_31

PPB_Periph

PPB_Periph : aliased PPB_Peripheral
  with Import, Address => PPB_Base;

PPB_Peripheral

type PPB_Peripheral is record
   SYST_CSR   : aliased SYST_CSR_Register;
   SYST_RVR   : aliased SYST_RVR_Register;
   SYST_CVR   : aliased SYST_CVR_Register;
   SYST_CALIB : aliased SYST_CALIB_Register;
   NVIC_ISER  : aliased HAL.UInt32;
   NVIC_ICER  : aliased HAL.UInt32;
   NVIC_ISPR  : aliased HAL.UInt32;
   NVIC_ICPR  : aliased HAL.UInt32;
   NVIC_IPR0  : aliased NVIC_IPR0_Register;
   NVIC_IPR1  : aliased NVIC_IPR1_Register;
   NVIC_IPR2  : aliased NVIC_IPR2_Register;
   NVIC_IPR3  : aliased NVIC_IPR3_Register;
   NVIC_IPR4  : aliased NVIC_IPR4_Register;
   NVIC_IPR5  : aliased NVIC_IPR5_Register;
   NVIC_IPR6  : aliased NVIC_IPR6_Register;
   NVIC_IPR7  : aliased NVIC_IPR7_Register;
   CPUID      : aliased CPUID_Register;
   ICSR       : aliased ICSR_Register;
   VTOR       : aliased VTOR_Register;
   AIRCR      : aliased AIRCR_Register;
   SCR        : aliased SCR_Register;
   CCR        : aliased CCR_Register;
   SHPR2      : aliased SHPR2_Register;
   SHPR3      : aliased SHPR3_Register;
   SHCSR      : aliased SHCSR_Register;
   MPU_TYPE   : aliased MPU_TYPE_Register;
   MPU_CTRL   : aliased MPU_CTRL_Register;
   MPU_RNR    : aliased MPU_RNR_Register;
   MPU_RBAR   : aliased MPU_RBAR_Register;
   MPU_RASR   : aliased MPU_RASR_Register;
end record;
Record fields
SYST_CSR

Use the SysTick Reload Value Register to specify the start value to load into the current value register when the counter reaches 0. It can be any value between 0 and 0x00FFFFFF. A start value of 0 is possible, but has no effect because the SysTick interrupt and COUNTFLAG are activated when counting from 1 to 0. The reset value of this register is UNKNOWN.\n To generate a multi-shot timer with a period of N processor clock cycles, use a RELOAD value of N-1. For example, if the SysTick interrupt is required every 100 clock pulses, set RELOAD to 99.

SYST_RVR

Use the SysTick Current Value Register to find the current value in the register. The reset value of this register is UNKNOWN.

SYST_CVR

Use the SysTick Calibration Value Register to enable software to scale to any required speed using divide and multiply.

SYST_CALIB

Use the Interrupt Set-Enable Register to enable interrupts and determine which interrupts are currently enabled.\n If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC never activates the interrupt, regardless of its priority.

NVIC_ISER

Use the Interrupt Clear-Enable Registers to disable interrupts and determine which interrupts are currently enabled.

NVIC_ICER

The NVIC_ISPR forces interrupts into the pending state, and shows which interrupts are pending.

NVIC_ISPR

Use the Interrupt Clear-Pending Register to clear pending interrupts and determine which interrupts are currently pending.

NVIC_ICPR

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.\n Note: Writing 1 to an NVIC_ICPR bit does not affect the active state of the corresponding interrupt.\n These registers are only word-accessible

NVIC_IPR0

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR1

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR2

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR3

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR4

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR5

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR6

Use the Interrupt Priority Registers to assign a priority from 0 to 3 to each of the available interrupts. 0 is the highest priority, and 3 is the lowest.

NVIC_IPR7

Read the CPU ID Base Register to determine: the ID number of the processor core, the version number of the processor core, the implementation details of the processor core.

CPUID

Use the Interrupt Control State Register to set a pending Non-Maskable Interrupt (NMI), set or clear a pending PendSV, set or clear a pending SysTick, check for pending exceptions, check the vector number of the highest priority pended exception, check the vector number of the active exception.

ICSR

The VTOR holds the vector table offset address.

VTOR

Use the Application Interrupt and Reset Control Register to: determine data endianness, clear all active state information from debug halt mode, request a system reset.

AIRCR

System Control Register. Use the System Control Register for power-management functions: signal to the system when the processor can enter a low power state, control how the processor enters and exits low power states.

SCR

The Configuration and Control Register permanently enables stack alignment and causes unaligned accesses to result in a Hard Fault.

CCR

System handlers are a special class of exception handler that can have their priority set to any of the priority levels. Use the System Handler Priority Register 2 to set the priority of SVCall.

SHPR2

System handlers are a special class of exception handler that can have their priority set to any of the priority levels. Use the System Handler Priority Register 3 to set the priority of PendSV and SysTick.

SHPR3

Use the System Handler Control and State Register to determine or clear the pending status of SVCall.

SHCSR

Read the MPU Type Register to determine if the processor implements an MPU, and how many regions the MPU supports.

MPU_TYPE

Use the MPU Control Register to enable and disable the MPU, and to control whether the default memory map is enabled as a background region for privileged accesses, and whether the MPU is enabled for HardFaults and NMIs.

MPU_CTRL

Use the MPU Region Number Register to select the region currently accessed by MPU_RBAR and MPU_RASR.

MPU_RNR

Read the MPU Region Base Address Register to determine the base address of the region identified by MPU_RNR. Write to update the base address of said region or that of a specified region, with whose number MPU_RNR will also be updated.

MPU_RBAR

Use the MPU Region Attribute and Size Register to define the size, access behaviour and memory type of the region identified by MPU_RNR, and enable that region.

MPU_RASR

SCR_Register

type SCR_Register is record
   Reserved_0_0  : HAL.Bit := 16#0#;
   SLEEPONEXIT   : Boolean := False;
   SLEEPDEEP     : Boolean := False;
   Reserved_3_3  : HAL.Bit := 16#0#;
   SEVONPEND     : Boolean := False;
   Reserved_5_31 : HAL.UInt27 := 16#0#;
end record;
Record fields
Reserved_0_0

Indicates sleep-on-exit when returning from Handler mode to Thread mode:\n 0 = Do not sleep when returning to Thread mode.\n 1 = Enter sleep, or deep sleep, on return from an ISR to Thread mode.\n Setting this bit to 1 enables an interrupt driven application to avoid returning to an empty main application.

SLEEPONEXIT

Controls whether the processor uses sleep or deep sleep as its low power mode:\n 0 = Sleep.\n 1 = Deep sleep.

SLEEPDEEP

unspecified

Reserved_3_3

Send Event on Pending bit:\n 0 = Only enabled interrupts or events can wakeup the processor, disabled interrupts are excluded.\n 1 = Enabled events and all interrupts, including disabled interrupts, can wakeup the processor.\n When an event or interrupt becomes pending, the event signal wakes up the processor from WFE. If the\n processor is not waiting for an event, the event is registered and affects the next WFE.\n The processor also wakes up on execution of an SEV instruction or an external event.

SEVONPEND

unspecified

Reserved_5_31

SHCSR_Register

type SHCSR_Register is record
   Reserved_0_14  : HAL.UInt15 := 16#0#;
   SVCALLPENDED   : Boolean := False;
   Reserved_16_31 : HAL.UInt16 := 16#0#;
end record;
Record fields
Reserved_0_14

Reads as 1 if SVCall is Pending. Write 1 to set pending SVCall, write 0 to clear pending SVCall.

SVCALLPENDED

unspecified

Reserved_16_31

SHPR2_PRI_11_Field

subtype SHPR2_PRI_11_Field is HAL.UInt2;

SHPR2_Register

type SHPR2_Register is record
   Reserved_0_29 : HAL.UInt30 := 16#0#;
   PRI_11        : SHPR2_PRI_11_Field := 16#0#;
end record;
Record fields
Reserved_0_29

Priority of system handler 11, SVCall

PRI_11

SHPR3_PRI_14_Field

subtype SHPR3_PRI_14_Field is HAL.UInt2;

SHPR3_PRI_15_Field

subtype SHPR3_PRI_15_Field is HAL.UInt2;

SHPR3_Register

type SHPR3_Register is record
   Reserved_0_21  : HAL.UInt22 := 16#0#;
   PRI_14         : SHPR3_PRI_14_Field := 16#0#;
   Reserved_24_29 : HAL.UInt6 := 16#0#;
   PRI_15         : SHPR3_PRI_15_Field := 16#0#;
end record;
Record fields
Reserved_0_21

Priority of system handler 14, PendSV

PRI_14

unspecified

Reserved_24_29

Priority of system handler 15, SysTick

PRI_15

SYST_CALIB_Register

type SYST_CALIB_Register is record
   TENMS          : SYST_CALIB_TENMS_Field;
   Reserved_24_29 : HAL.UInt6;
   SKEW           : Boolean;
   NOREF          : Boolean;
end record;
Record fields
TENMS

unspecified

Reserved_24_29

Read-only. If reads as 1, the calibration value for 10ms is inexact (due to clock frequency).

SKEW

Read-only. If reads as 1, the Reference clock is not provided - the CLKSOURCE bit of the SysTick Control and Status register will be forced to 1 and cannot be cleared to 0.

NOREF

SYST_CALIB_TENMS_Field

subtype SYST_CALIB_TENMS_Field is HAL.UInt24;

SYST_CSR_Register

type SYST_CSR_Register is record
   ENABLE         : Boolean := False;
   TICKINT        : Boolean := False;
   CLKSOURCE      : Boolean := False;
   Reserved_3_15  : HAL.UInt13 := 16#0#;
   COUNTFLAG      : Boolean := False;
   Reserved_17_31 : HAL.UInt15 := 16#0#;
end record;
Record fields
ENABLE

Enables SysTick exception request:\n 0 = Counting down to zero does not assert the SysTick exception request.\n 1 = Counting down to zero to asserts the SysTick exception request.

TICKINT

SysTick clock source. Always reads as one if SYST_CALIB reports NOREF.\n Selects the SysTick timer clock source:\n 0 = External reference clock.\n 1 = Processor clock.

CLKSOURCE

unspecified

Reserved_3_15

Read-only. Returns 1 if timer counted to 0 since last time this was read. Clears on read by application or debugger.

COUNTFLAG

unspecified

Reserved_17_31

SYST_CVR_CURRENT_Field

subtype SYST_CVR_CURRENT_Field is HAL.UInt24;

SYST_CVR_Register

type SYST_CVR_Register is record
   CURRENT        : SYST_CVR_CURRENT_Field := 16#0#;
   Reserved_24_31 : HAL.UInt8 := 16#0#;
end record;
Record fields
CURRENT

unspecified

Reserved_24_31

SYST_RVR_Register

type SYST_RVR_Register is record
   RELOAD         : SYST_RVR_RELOAD_Field := 16#0#;
   Reserved_24_31 : HAL.UInt8 := 16#0#;
end record;
Record fields
RELOAD

unspecified

Reserved_24_31

SYST_RVR_RELOAD_Field

subtype SYST_RVR_RELOAD_Field is HAL.UInt24;

VTOR_Register

type VTOR_Register is record
   Reserved_0_7 : HAL.UInt8 := 16#0#;
   TBLOFF       : VTOR_TBLOFF_Field := 16#0#;
end record;
Record fields
Reserved_0_7

Bits [31:8] of the indicate the vector table offset address.

TBLOFF

VTOR_TBLOFF_Field

subtype VTOR_TBLOFF_Field is HAL.UInt24;