RP2040_SVD.UART

Entities

Array Types

Record Types

Subtypes

Variables

Description

------------- Registers -- -------------

UART0_Periph

UART0_Periph : aliased UART_Peripheral
  with Import, Address => UART0_Base;

UART1_Periph

UART1_Periph : aliased UART_Peripheral
  with Import, Address => UART1_Base;

UART_Peripheral

type UART_Peripheral is record
   UARTDR        : aliased UARTDR_Register;
   UARTRSR       : aliased UARTRSR_Register;
   UARTFR        : aliased UARTFR_Register;
   UARTILPR      : aliased UARTILPR_Register;
   UARTIBRD      : aliased UARTIBRD_Register;
   UARTFBRD      : aliased UARTFBRD_Register;
   UARTLCR_H     : aliased UARTLCR_H_Register;
   UARTCR        : aliased UARTCR_Register;
   UARTIFLS      : aliased UARTIFLS_Register;
   UARTIMSC      : aliased UARTIMSC_Register;
   UARTRIS       : aliased UARTRIS_Register;
   UARTMIS       : aliased UARTMIS_Register;
   UARTICR       : aliased UARTICR_Register;
   UARTDMACR     : aliased UARTDMACR_Register;
   UARTPERIPHID0 : aliased UARTPERIPHID0_Register;
   UARTPERIPHID1 : aliased UARTPERIPHID1_Register;
   UARTPERIPHID2 : aliased UARTPERIPHID2_Register;
   UARTPERIPHID3 : aliased UARTPERIPHID3_Register;
   UARTPCELLID0  : aliased UARTPCELLID0_Register;
   UARTPCELLID1  : aliased UARTPCELLID1_Register;
   UARTPCELLID2  : aliased UARTPCELLID2_Register;
   UARTPCELLID3  : aliased UARTPCELLID3_Register;
end record;
Record fields
UARTDR

Receive Status Register/Error Clear Register, UARTRSR/UARTECR

UARTRSR

Flag Register, UARTFR

UARTFR

IrDA Low-Power Counter Register, UARTILPR

UARTILPR

Integer Baud Rate Register, UARTIBRD

UARTIBRD

Fractional Baud Rate Register, UARTFBRD

UARTFBRD

Line Control Register, UARTLCR_H

UARTLCR_H

Control Register, UARTCR

UARTCR

Interrupt FIFO Level Select Register, UARTIFLS

UARTIFLS

Interrupt Mask Set/Clear Register, UARTIMSC

UARTIMSC

Raw Interrupt Status Register, UARTRIS

UARTRIS

Masked Interrupt Status Register, UARTMIS

UARTMIS

Interrupt Clear Register, UARTICR

UARTICR

DMA Control Register, UARTDMACR

UARTDMACR

UARTPeriphID0 Register

UARTPERIPHID0

UARTPeriphID1 Register

UARTPERIPHID1

UARTPeriphID2 Register

UARTPERIPHID2

UARTPeriphID3 Register

UARTPERIPHID3

UARTPCellID0 Register

UARTPCELLID0

UARTPCellID1 Register

UARTPCELLID1

UARTPCellID2 Register

UARTPCELLID2

UARTPCellID3 Register

UARTPCELLID3

UARTCR_OUT_Field

type UARTCR_OUT_Field
  (As_Array : Boolean := False)
is record
   case As_Array is
      when False =>
         Val : HAL.UInt2;
      when True =>
         Arr : UARTCR_OUT_Field_Array;
   end case;
end record;
Record fields
As_Array
Val
Arr

UARTCR_OUT_Field_Array

type UARTCR_OUT_Field_Array is array (1 .. 2) of Boolean
  with Component_Size => 1, Size => 2;

UARTCR_Register

type UARTCR_Register is record
   UARTEN         : Boolean := False;
   SIREN          : Boolean := False;
   SIRLP          : Boolean := False;
   Reserved_3_6   : HAL.UInt4 := 16#0#;
   LBE            : Boolean := False;
   TXE            : Boolean := True;
   RXE            : Boolean := True;
   DTR            : Boolean := False;
   RTS            : Boolean := False;
   OUT_k          : UARTCR_OUT_Field := (As_Array => False, Val => 16#0#);
   RTSEN          : Boolean := False;
   CTSEN          : Boolean := False;
   Reserved_16_31 : HAL.UInt16 := 16#0#;
end record;
Record fields
UARTEN

SIR enable: 0 = IrDA SIR ENDEC is disabled. nSIROUT remains LOW (no light pulse generated), and signal transitions on SIRIN have no effect. 1 = IrDA SIR ENDEC is enabled. Data is transmitted and received on nSIROUT and SIRIN. UARTTXD remains HIGH, in the marking state. Signal transitions on UARTRXD or modem status inputs have no effect. This bit has no effect if the UARTEN bit disables the UART.

SIREN

SIR low-power IrDA mode. This bit selects the IrDA encoding mode. If this bit is cleared to 0, low-level bits are transmitted as an active high pulse with a width of 3 / 16th of the bit period. If this bit is set to 1, low-level bits are transmitted with a pulse width that is 3 times the period of the IrLPBaud16 input signal, regardless of the selected bit rate. Setting this bit uses less power, but might reduce transmission distances.

SIRLP

unspecified

Reserved_3_6

Loopback enable. If this bit is set to 1 and the SIREN bit is set to 1 and the SIRTEST bit in the Test Control Register, UARTTCR is set to 1, then the nSIROUT path is inverted, and fed through to the SIRIN path. The SIRTEST bit in the test register must be set to 1 to override the normal half-duplex SIR operation. This must be the requirement for accessing the test registers during normal operation, and SIRTEST must be cleared to 0 when loopback testing is finished. This feature reduces the amount of external coupling required during system test. If this bit is set to 1, and the SIRTEST bit is set to 0, the UARTTXD path is fed through to the UARTRXD path. In either SIR mode or UART mode, when this bit is set, the modem outputs are also fed through to the modem inputs. This bit is cleared to 0 on reset, to disable loopback.

LBE

Transmit enable. If this bit is set to 1, the transmit section of the UART is enabled. Data transmission occurs for either UART signals, or SIR signals depending on the setting of the SIREN bit. When the UART is disabled in the middle of transmission, it completes the current character before stopping.

TXE

Receive enable. If this bit is set to 1, the receive section of the UART is enabled. Data reception occurs for either UART signals or SIR signals depending on the setting of the SIREN bit. When the UART is disabled in the middle of reception, it completes the current character before stopping.

RXE

Data transmit ready. This bit is the complement of the UART data transmit ready, nUARTDTR, modem status output. That is, when the bit is programmed to a 1 then nUARTDTR is LOW.

DTR

Request to send. This bit is the complement of the UART request to send, nUARTRTS, modem status output. That is, when the bit is programmed to a 1 then nUARTRTS is LOW.

RTS

This bit is the complement of the UART Out1 (nUARTOut1) modem status output. That is, when the bit is programmed to a 1 the output is 0. For DTE this can be used as Data Carrier Detect (DCD).

OUT_k

RTS hardware flow control enable. If this bit is set to 1, RTS hardware flow control is enabled. Data is only requested when there is space in the receive FIFO for it to be received.

RTSEN

CTS hardware flow control enable. If this bit is set to 1, CTS hardware flow control is enabled. Data is only transmitted when the nUARTCTS signal is asserted.

CTSEN

unspecified

Reserved_16_31

UARTDMACR_Register

type UARTDMACR_Register is record
   RXDMAE        : Boolean := False;
   TXDMAE        : Boolean := False;
   DMAONERR      : Boolean := False;
   Reserved_3_31 : HAL.UInt29 := 16#0#;
end record;
Record fields
RXDMAE

Transmit DMA enable. If this bit is set to 1, DMA for the transmit FIFO is enabled.

TXDMAE

DMA on error. If this bit is set to 1, the DMA receive request outputs, UARTRXDMASREQ or UARTRXDMABREQ, are disabled when the UART error interrupt is asserted.

DMAONERR

unspecified

Reserved_3_31

UARTDR_DATA_Field

subtype UARTDR_DATA_Field is HAL.UInt8;

UARTDR_Register

type UARTDR_Register is record
   DATA           : UARTDR_DATA_Field := 16#0#;
   FE             : Boolean := False;
   PE             : Boolean := False;
   BE             : Boolean := False;
   OE             : Boolean := False;
   Reserved_12_31 : HAL.UInt20 := 16#0#;
end record;
Record fields
DATA

Read-only. Framing error. When set to 1, it indicates that the received character did not have a valid stop bit (a valid stop bit is 1). In FIFO mode, this error is associated with the character at the top of the FIFO.

FE

Read-only. Parity error. When set to 1, it indicates that the parity of the received data character does not match the parity that the EPS and SPS bits in the Line Control Register, UARTLCR_H. In FIFO mode, this error is associated with the character at the top of the FIFO.

PE

Read-only. Break error. This bit is set to 1 if a break condition was detected, indicating that the received data input was held LOW for longer than a full-word transmission time (defined as start, data, parity and stop bits). In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the receive data input goes to a 1 (marking state), and the next valid start bit is received.

BE

Read-only. Overrun error. This bit is set to 1 if data is received and the receive FIFO is already full. This is cleared to 0 once there is an empty space in the FIFO and a new character can be written to it.

OE

unspecified

Reserved_12_31

UARTFBRD_BAUD_DIVFRAC_Field

subtype UARTFBRD_BAUD_DIVFRAC_Field is HAL.UInt6;

UARTFBRD_Register

type UARTFBRD_Register is record
   BAUD_DIVFRAC  : UARTFBRD_BAUD_DIVFRAC_Field := 16#0#;
   Reserved_6_31 : HAL.UInt26 := 16#0#;
end record;
Record fields
BAUD_DIVFRAC

unspecified

Reserved_6_31

UARTFR_Register

type UARTFR_Register is record
   CTS           : Boolean;
   DSR           : Boolean;
   DCD           : Boolean;
   BUSY          : Boolean;
   RXFE          : Boolean;
   TXFF          : Boolean;
   RXFF          : Boolean;
   TXFE          : Boolean;
   RI            : Boolean;
   Reserved_9_31 : HAL.UInt23;
end record;
Record fields
CTS

Read-only. Data set ready. This bit is the complement of the UART data set ready, nUARTDSR, modem status input. That is, the bit is 1 when nUARTDSR is LOW.

DSR

Read-only. Data carrier detect. This bit is the complement of the UART data carrier detect, nUARTDCD, modem status input. That is, the bit is 1 when nUARTDCD is LOW.

DCD

Read-only. UART busy. If this bit is set to 1, the UART is busy transmitting data. This bit remains set until the complete byte, including all the stop bits, has been sent from the shift register. This bit is set as soon as the transmit FIFO becomes non-empty, regardless of whether the UART is enabled or not.

BUSY

Read-only. Receive FIFO empty. The meaning of this bit depends on the state of the FEN bit in the UARTLCR_H Register. If the FIFO is disabled, this bit is set when the receive holding register is empty. If the FIFO is enabled, the RXFE bit is set when the receive FIFO is empty.

RXFE

Read-only. Transmit FIFO full. The meaning of this bit depends on the state of the FEN bit in the UARTLCR_H Register. If the FIFO is disabled, this bit is set when the transmit holding register is full. If the FIFO is enabled, the TXFF bit is set when the transmit FIFO is full.

TXFF

Read-only. Receive FIFO full. The meaning of this bit depends on the state of the FEN bit in the UARTLCR_H Register. If the FIFO is disabled, this bit is set when the receive holding register is full. If the FIFO is enabled, the RXFF bit is set when the receive FIFO is full.

RXFF

Read-only. Transmit FIFO empty. The meaning of this bit depends on the state of the FEN bit in the Line Control Register, UARTLCR_H. If the FIFO is disabled, this bit is set when the transmit holding register is empty. If the FIFO is enabled, the TXFE bit is set when the transmit FIFO is empty. This bit does not indicate if there is data in the transmit shift register.

TXFE

Read-only. Ring indicator. This bit is the complement of the UART ring indicator, nUARTRI, modem status input. That is, the bit is 1 when nUARTRI is LOW.

RI

unspecified

Reserved_9_31

UARTIBRD_BAUD_DIVINT_Field

subtype UARTIBRD_BAUD_DIVINT_Field is HAL.UInt16;

UARTIBRD_Register

type UARTIBRD_Register is record
   BAUD_DIVINT    : UARTIBRD_BAUD_DIVINT_Field := 16#0#;
   Reserved_16_31 : HAL.UInt16 := 16#0#;
end record;
Record fields
BAUD_DIVINT

unspecified

Reserved_16_31

UARTICR_Register

type UARTICR_Register is record
   RIMIC          : Boolean := False;
   CTSMIC         : Boolean := False;
   DCDMIC         : Boolean := False;
   DSRMIC         : Boolean := False;
   RXIC           : Boolean := False;
   TXIC           : Boolean := False;
   RTIC           : Boolean := False;
   FEIC           : Boolean := False;
   PEIC           : Boolean := False;
   BEIC           : Boolean := False;
   OEIC           : Boolean := False;
   Reserved_11_31 : HAL.UInt21 := 16#0#;
end record;
Record fields
RIMIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. nUARTCTS modem interrupt clear. Clears the UARTCTSINTR interrupt.

CTSMIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. nUARTDCD modem interrupt clear. Clears the UARTDCDINTR interrupt.

DCDMIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. nUARTDSR modem interrupt clear. Clears the UARTDSRINTR interrupt.

DSRMIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Receive interrupt clear. Clears the UARTRXINTR interrupt.

RXIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Transmit interrupt clear. Clears the UARTTXINTR interrupt.

TXIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Receive timeout interrupt clear. Clears the UARTRTINTR interrupt.

RTIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Framing error interrupt clear. Clears the UARTFEINTR interrupt.

FEIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Parity error interrupt clear. Clears the UARTPEINTR interrupt.

PEIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Break error interrupt clear. Clears the UARTBEINTR interrupt.

BEIC

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Overrun error interrupt clear. Clears the UARTOEINTR interrupt.

OEIC

unspecified

Reserved_11_31

UARTIFLS_Register

type UARTIFLS_Register is record
   TXIFLSEL      : UARTIFLS_TXIFLSEL_Field := 16#2#;
   RXIFLSEL      : UARTIFLS_RXIFLSEL_Field := 16#2#;
   Reserved_6_31 : HAL.UInt26 := 16#0#;
end record;
Record fields
TXIFLSEL

Receive interrupt FIFO level select. The trigger points for the receive interrupt are as follows: b000 = Receive FIFO becomes >= 1 / 8 full b001 = Receive FIFO becomes >= 1 / 4 full b010 = Receive FIFO becomes >= 1 / 2 full b011 = Receive FIFO becomes >= 3 / 4 full b100 = Receive FIFO becomes >= 7 / 8 full b101-b111 = reserved.

RXIFLSEL

unspecified

Reserved_6_31

UARTIFLS_RXIFLSEL_Field

subtype UARTIFLS_RXIFLSEL_Field is HAL.UInt3;

UARTIFLS_TXIFLSEL_Field

subtype UARTIFLS_TXIFLSEL_Field is HAL.UInt3;

UARTILPR_ILPDVSR_Field

subtype UARTILPR_ILPDVSR_Field is HAL.UInt8;

UARTILPR_Register

type UARTILPR_Register is record
   ILPDVSR       : UARTILPR_ILPDVSR_Field := 16#0#;
   Reserved_8_31 : HAL.UInt24 := 16#0#;
end record;
Record fields
ILPDVSR

unspecified

Reserved_8_31

UARTIMSC_Register

type UARTIMSC_Register is record
   RIMIM          : Boolean := False;
   CTSMIM         : Boolean := False;
   DCDMIM         : Boolean := False;
   DSRMIM         : Boolean := False;
   RXIM           : Boolean := False;
   TXIM           : Boolean := False;
   RTIM           : Boolean := False;
   FEIM           : Boolean := False;
   PEIM           : Boolean := False;
   BEIM           : Boolean := False;
   OEIM           : Boolean := False;
   Reserved_11_31 : HAL.UInt21 := 16#0#;
end record;
Record fields
RIMIM

nUARTCTS modem interrupt mask. A read returns the current mask for the UARTCTSINTR interrupt. On a write of 1, the mask of the UARTCTSINTR interrupt is set. A write of 0 clears the mask.

CTSMIM

nUARTDCD modem interrupt mask. A read returns the current mask for the UARTDCDINTR interrupt. On a write of 1, the mask of the UARTDCDINTR interrupt is set. A write of 0 clears the mask.

DCDMIM

nUARTDSR modem interrupt mask. A read returns the current mask for the UARTDSRINTR interrupt. On a write of 1, the mask of the UARTDSRINTR interrupt is set. A write of 0 clears the mask.

DSRMIM

Receive interrupt mask. A read returns the current mask for the UARTRXINTR interrupt. On a write of 1, the mask of the UARTRXINTR interrupt is set. A write of 0 clears the mask.

RXIM

Transmit interrupt mask. A read returns the current mask for the UARTTXINTR interrupt. On a write of 1, the mask of the UARTTXINTR interrupt is set. A write of 0 clears the mask.

TXIM

Receive timeout interrupt mask. A read returns the current mask for the UARTRTINTR interrupt. On a write of 1, the mask of the UARTRTINTR interrupt is set. A write of 0 clears the mask.

RTIM

Framing error interrupt mask. A read returns the current mask for the UARTFEINTR interrupt. On a write of 1, the mask of the UARTFEINTR interrupt is set. A write of 0 clears the mask.

FEIM

Parity error interrupt mask. A read returns the current mask for the UARTPEINTR interrupt. On a write of 1, the mask of the UARTPEINTR interrupt is set. A write of 0 clears the mask.

PEIM

Break error interrupt mask. A read returns the current mask for the UARTBEINTR interrupt. On a write of 1, the mask of the UARTBEINTR interrupt is set. A write of 0 clears the mask.

BEIM

Overrun error interrupt mask. A read returns the current mask for the UARTOEINTR interrupt. On a write of 1, the mask of the UARTOEINTR interrupt is set. A write of 0 clears the mask.

OEIM

unspecified

Reserved_11_31

UARTLCR_H_Register

type UARTLCR_H_Register is record
   BRK           : Boolean := False;
   PEN           : Boolean := False;
   EPS           : Boolean := False;
   STP2          : Boolean := False;
   FEN           : Boolean := False;
   WLEN          : UARTLCR_H_WLEN_Field := 16#0#;
   SPS           : Boolean := False;
   Reserved_8_31 : HAL.UInt24 := 16#0#;
end record;
Record fields
BRK

Parity enable: 0 = parity is disabled and no parity bit added to the data frame 1 = parity checking and generation is enabled.

PEN

Even parity select. Controls the type of parity the UART uses during transmission and reception: 0 = odd parity. The UART generates or checks for an odd number of 1s in the data and parity bits. 1 = even parity. The UART generates or checks for an even number of 1s in the data and parity bits. This bit has no effect when the PEN bit disables parity checking and generation.

EPS

Two stop bits select. If this bit is set to 1, two stop bits are transmitted at the end of the frame. The receive logic does not check for two stop bits being received.

STP2

Enable FIFOs: 0 = FIFOs are disabled (character mode) that is, the FIFOs become 1-byte-deep holding registers 1 = transmit and receive FIFO buffers are enabled (FIFO mode).

FEN

Word length. These bits indicate the number of data bits transmitted or received in a frame as follows: b11 = 8 bits b10 = 7 bits b01 = 6 bits b00 = 5 bits.

WLEN

Stick parity select. 0 = stick parity is disabled 1 = either: * if the EPS bit is 0 then the parity bit is transmitted and checked as a 1 * if the EPS bit is 1 then the parity bit is transmitted and checked as a 0. This bit has no effect when the PEN bit disables parity checking and generation.

SPS

unspecified

Reserved_8_31

UARTLCR_H_WLEN_Field

subtype UARTLCR_H_WLEN_Field is HAL.UInt2;

UARTMIS_Register

type UARTMIS_Register is record
   RIMMIS         : Boolean;
   CTSMMIS        : Boolean;
   DCDMMIS        : Boolean;
   DSRMMIS        : Boolean;
   RXMIS          : Boolean;
   TXMIS          : Boolean;
   RTMIS          : Boolean;
   FEMIS          : Boolean;
   PEMIS          : Boolean;
   BEMIS          : Boolean;
   OEMIS          : Boolean;
   Reserved_11_31 : HAL.UInt21;
end record;
Record fields
RIMMIS

Read-only. nUARTCTS modem masked interrupt status. Returns the masked interrupt state of the UARTCTSINTR interrupt.

CTSMMIS

Read-only. nUARTDCD modem masked interrupt status. Returns the masked interrupt state of the UARTDCDINTR interrupt.

DCDMMIS

Read-only. nUARTDSR modem masked interrupt status. Returns the masked interrupt state of the UARTDSRINTR interrupt.

DSRMMIS

Read-only. Receive masked interrupt status. Returns the masked interrupt state of the UARTRXINTR interrupt.

RXMIS

Read-only. Transmit masked interrupt status. Returns the masked interrupt state of the UARTTXINTR interrupt.

TXMIS

Read-only. Receive timeout masked interrupt status. Returns the masked interrupt state of the UARTRTINTR interrupt.

RTMIS

Read-only. Framing error masked interrupt status. Returns the masked interrupt state of the UARTFEINTR interrupt.

FEMIS

Read-only. Parity error masked interrupt status. Returns the masked interrupt state of the UARTPEINTR interrupt.

PEMIS

Read-only. Break error masked interrupt status. Returns the masked interrupt state of the UARTBEINTR interrupt.

BEMIS

Read-only. Overrun error masked interrupt status. Returns the masked interrupt state of the UARTOEINTR interrupt.

OEMIS

unspecified

Reserved_11_31

UARTPCELLID0_Register

type UARTPCELLID0_Register is record
   UARTPCELLID0  : UARTPCELLID0_UARTPCELLID0_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
UARTPCELLID0

unspecified

Reserved_8_31

UARTPCELLID0_UARTPCELLID0_Field

subtype UARTPCELLID0_UARTPCELLID0_Field is HAL.UInt8;

UARTPCELLID1_Register

type UARTPCELLID1_Register is record
   UARTPCELLID1  : UARTPCELLID1_UARTPCELLID1_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
UARTPCELLID1

unspecified

Reserved_8_31

UARTPCELLID1_UARTPCELLID1_Field

subtype UARTPCELLID1_UARTPCELLID1_Field is HAL.UInt8;

UARTPCELLID2_Register

type UARTPCELLID2_Register is record
   UARTPCELLID2  : UARTPCELLID2_UARTPCELLID2_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
UARTPCELLID2

unspecified

Reserved_8_31

UARTPCELLID2_UARTPCELLID2_Field

subtype UARTPCELLID2_UARTPCELLID2_Field is HAL.UInt8;

UARTPCELLID3_Register

type UARTPCELLID3_Register is record
   UARTPCELLID3  : UARTPCELLID3_UARTPCELLID3_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
UARTPCELLID3

unspecified

Reserved_8_31

UARTPCELLID3_UARTPCELLID3_Field

subtype UARTPCELLID3_UARTPCELLID3_Field is HAL.UInt8;

UARTPERIPHID0_PARTNUMBER0_Field

subtype UARTPERIPHID0_PARTNUMBER0_Field is HAL.UInt8;

UARTPERIPHID0_Register

type UARTPERIPHID0_Register is record
   PARTNUMBER0   : UARTPERIPHID0_PARTNUMBER0_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
PARTNUMBER0

unspecified

Reserved_8_31

UARTPERIPHID1_DESIGNER0_Field

subtype UARTPERIPHID1_DESIGNER0_Field is HAL.UInt4;

UARTPERIPHID1_PARTNUMBER1_Field

subtype UARTPERIPHID1_PARTNUMBER1_Field is HAL.UInt4;

UARTPERIPHID1_Register

type UARTPERIPHID1_Register is record
   PARTNUMBER1   : UARTPERIPHID1_PARTNUMBER1_Field;
   DESIGNER0     : UARTPERIPHID1_DESIGNER0_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
PARTNUMBER1

Read-only. These bits read back as 0x1

DESIGNER0

unspecified

Reserved_8_31

UARTPERIPHID2_DESIGNER1_Field

subtype UARTPERIPHID2_DESIGNER1_Field is HAL.UInt4;

UARTPERIPHID2_Register

type UARTPERIPHID2_Register is record
   DESIGNER1     : UARTPERIPHID2_DESIGNER1_Field;
   REVISION      : UARTPERIPHID2_REVISION_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
DESIGNER1

Read-only. This field depends on the revision of the UART: r1p0 0x0 r1p1 0x1 r1p3 0x2 r1p4 0x2 r1p5 0x3

REVISION

unspecified

Reserved_8_31

UARTPERIPHID2_REVISION_Field

subtype UARTPERIPHID2_REVISION_Field is HAL.UInt4;

UARTPERIPHID3_CONFIGURATION_Field

subtype UARTPERIPHID3_CONFIGURATION_Field is HAL.UInt8;

UARTPERIPHID3_Register

type UARTPERIPHID3_Register is record
   CONFIGURATION : UARTPERIPHID3_CONFIGURATION_Field;
   Reserved_8_31 : HAL.UInt24;
end record;
Record fields
CONFIGURATION

unspecified

Reserved_8_31

UARTRIS_Register

type UARTRIS_Register is record
   RIRMIS         : Boolean;
   CTSRMIS        : Boolean;
   DCDRMIS        : Boolean;
   DSRRMIS        : Boolean;
   RXRIS          : Boolean;
   TXRIS          : Boolean;
   RTRIS          : Boolean;
   FERIS          : Boolean;
   PERIS          : Boolean;
   BERIS          : Boolean;
   OERIS          : Boolean;
   Reserved_11_31 : HAL.UInt21;
end record;
Record fields
RIRMIS

Read-only. nUARTCTS modem interrupt status. Returns the raw interrupt state of the UARTCTSINTR interrupt.

CTSRMIS

Read-only. nUARTDCD modem interrupt status. Returns the raw interrupt state of the UARTDCDINTR interrupt.

DCDRMIS

Read-only. nUARTDSR modem interrupt status. Returns the raw interrupt state of the UARTDSRINTR interrupt.

DSRRMIS

Read-only. Receive interrupt status. Returns the raw interrupt state of the UARTRXINTR interrupt.

RXRIS

Read-only. Transmit interrupt status. Returns the raw interrupt state of the UARTTXINTR interrupt.

TXRIS

Read-only. Receive timeout interrupt status. Returns the raw interrupt state of the UARTRTINTR interrupt. a

RTRIS

Read-only. Framing error interrupt status. Returns the raw interrupt state of the UARTFEINTR interrupt.

FERIS

Read-only. Parity error interrupt status. Returns the raw interrupt state of the UARTPEINTR interrupt.

PERIS

Read-only. Break error interrupt status. Returns the raw interrupt state of the UARTBEINTR interrupt.

BERIS

Read-only. Overrun error interrupt status. Returns the raw interrupt state of the UARTOEINTR interrupt.

OERIS

unspecified

Reserved_11_31

UARTRSR_Register

type UARTRSR_Register is record
   FE            : Boolean := False;
   PE            : Boolean := False;
   BE            : Boolean := False;
   OE            : Boolean := False;
   Reserved_4_31 : HAL.UInt28 := 16#0#;
end record;
Record fields
FE

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Parity error. When set to 1, it indicates that the parity of the received data character does not match the parity that the EPS and SPS bits in the Line Control Register, UARTLCR_H. This bit is cleared to 0 by a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO.

PE

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Break error. This bit is set to 1 if a break condition was detected, indicating that the received data input was held LOW for longer than a full-word transmission time (defined as start, data, parity, and stop bits). This bit is cleared to 0 after a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the receive data input goes to a 1 (marking state) and the next valid start bit is received.

BE

Write data bit of one shall clear (set to zero) the corresponding bit in the field. Overrun error. This bit is set to 1 if data is received and the FIFO is already full. This bit is cleared to 0 by a write to UARTECR. The FIFO contents remain valid because no more data is written when the FIFO is full, only the contents of the shift register are overwritten. The CPU must now read the data, to empty the FIFO.

OE

unspecified

Reserved_4_31